It's 10pm, it's 12°F outside, and the house is getting cold. Before you pick up the phone, there's a real chance you can find, and sometimes even fix, the problem yourself in under ten minutes. Not every no-heat call is a mechanical failure; a lot of them are a thermostat setting, a tripped switch, or a full condensate pan. Go through these in order. If you hit one of the stop conditions near the bottom, stop immediately and call: don't keep troubleshooting past that point.
1. Start at the thermostat
Check that it's actually set to Heat, not Off or Cool: easy to bump by accident, especially on a touchscreen. Confirm the setpoint is above room temperature. If it's a battery-powered thermostat, dead batteries will blank the screen or freeze it on a stale reading; swap in fresh AAs before doing anything else. If it's a smart thermostat, check that a schedule didn't silently revert overnight: some models reset to a factory schedule after a firmware update or a power blip. And if it's a smart thermostat wired without a dedicated C-wire (common on older systems retrofitted with a smart stat), a battery that's been trickle-charging off the system wiring can drop out and take the whole system offline with it: that's a legitimate, common cause of "the furnace just stopped."
2. Find the power switch
Furnaces and boilers have a dedicated power switch that looks exactly like a household light switch, usually mounted on or near the unit, or at the top of the basement stairs. It's easy to bump, and it's also sometimes flipped off intentionally during other work and never flipped back. Check it's in the "on" position. Then check the breaker panel: a furnace or boiler circuit that's tripped will usually show the breaker sitting in a middle, neither-on-nor-off position; push it firmly to off, then back to on.
3. Check the condensate pump
This is one of the most common, and most overlooked, causes of no-heat calls on high-efficiency furnaces and boilers. These units produce condensate as they run, and it has to be pumped out or drained away. If the condensate pump's reservoir fills up and the pump fails or the float switch trips, most systems will shut the burner down entirely rather than let the pan overflow. Look for a small pump and reservoir near the furnace; if it's full of water and the pump isn't running, that's very likely your culprit. Emptying it may restore heat immediately, but a pump that failed once will likely fail again soon: worth a service call even after it's working.
4. Check the filter
A badly clogged filter restricts airflow enough that the furnace can overheat internally and trip a high-limit safety switch, shutting the burner off as a protective measure. Pull the filter and hold it up to a light: if you can't see light through it, replace it. This is a five-minute fix that solves more no-heat calls than people expect.
5. Oil systems: check the tank and the reset button
If you heat with oil, check the tank gauge first: running out of oil is common enough that it's worth ruling out before anything else. If there's oil in the tank and the burner still won't fire, there's usually a reset button on the burner (often a small red button on the primary control, mounted on the burner housing).
6. Gas systems: pilot and ignition
On older gas furnaces with a standing pilot, check whether the pilot light is out: most have a lighting procedure printed on a label right on the unit. Newer furnaces use electronic ignition with no visible pilot; if those fail to ignite, you'll usually see a diagnostic light instead (see below) rather than being able to troubleshoot it by hand.
7. Check outdoor terminations after snow or ice
High-efficiency gas furnaces and boilers vent through PVC pipes that terminate on an exterior wall, close to grade. After a snowstorm, plow pile-up, or ice buildup, these can get blocked, and the unit's safety controls will shut it down rather than run with a blocked vent. Go outside with a flashlight and clear snow away from any PVC pipe terminations you can find on the house exterior, carefully, without forcing anything into the pipe itself.
8. Frozen condensate lines
In an unheated space (like an unconditioned area of a basement or garage) during a deep cold snap, the condensate drain line itself can freeze and back up, which trips the same safety switch as a full condensate pump. There's not much you can do about this on the spot beyond noting it for the technician: it usually means the line needs insulation or heat tape.
9. Read the blinking light
Most modern furnace and boiler control boards have a small LED that flashes a repeating pattern to indicate a specific fault code. There's usually a legend printed on a sticker inside the access panel or door. Count the flashes and note the pattern (for example, "2 flashes, pause, 2 flashes, pause"): even if you can't act on it yourself, this is exactly the information that lets a technician often diagnose the problem before arriving.
Stop: call instead of continuing to troubleshoot
While you're waiting for a technician
In a real cold snap, protecting the house matters as much as staying warm. Open cabinet doors under sinks on exterior walls so household heat can reach the pipes behind them. Let faucets on exterior-wall plumbing drip slightly to keep water moving. If you're using supplemental heat, an electric space heater on a dedicated circuit, kept clear of anything flammable, is reasonable for a night. Never use a gas range or oven for heat, and never run an unvented propane or kerosene heater indoors: both put carbon monoxide directly into your living space with no chimney to carry it away.
Make the service call count
When you do call, having a few things ready shortens the visit: the equipment brand and model number (usually on a sticker on the unit), a clear description of the symptom, what you've already checked or tried, and any error code or flash pattern you noted from the control board. Our office hours are Monday through Friday, 7am to 5pm, and emergency service is available outside those hours. We give priority same-day response to most routine no-heat calls: the details you gather beforehand help us bring the right part on the first trip.
If this ends up being the third or fourth no-heat call on an older furnace, it may be worth stepping back and asking whether repair still makes sense: our repair-or-replace guide walks through that decision, and you can reach out or book a visit when you're ready.
For more about this work, see our Emergency Service in southern NH page or request a free estimate.
Dana Borriello: Dana Borriello founded Service One Heating and Cooling in 2013 and still runs service calls across southern New Hampshire. He writes here about the questions homeowners actually ask on the truck.
