New Construction HVAC Design in Southern NH
Manual J load calculations, Manual D duct design, and Manual S equipment selection: done properly from plan review through commissioning, coordinated with your builder's schedule.
Why rule-of-thumb sizing fails
"500 square feet per ton" and similar rules of thumb ignore almost everything that actually determines a home's heating and cooling load: how the house is oriented to the sun, how much glass is on the south and west walls, how tight the building envelope is, how much infiltration the framing and air sealing allow, and what temperature extreme the system has to handle on the coldest and hottest days of the year. Two houses with identical square footage can have load calculations that differ by 30% or more once those factors are accounted for.
A Manual J load calculation, the ACCA industry standard, replaces the guess with room-by-room math using the home's actual construction: orientation, window area and glazing performance, wall and ceiling R-values, air infiltration rate, and the local winter and summer design temperatures. For southern New Hampshire, that design temperature is roughly 0°F in winter under IECC Climate Zone 6A, which sets the baseline insulation and air-sealing requirements the home is built to in the first place.
Manual D duct design
Right-sized equipment connected to poorly designed ductwork still underperforms. Manual D calculates the static pressure budget for the system and sizes trunk and branch ducts so the blower can actually push the designed airflow to every room, not just the rooms closest to the air handler.
Undersized return-air ducts are one of the most common problems we see in the field, whether in new construction or existing homes. A starved return raises static pressure, forces the blower to work harder, drives up energy use and noise, and undermines the performance the equipment was designed to deliver: regardless of how correctly it was sized on paper.
Manual S equipment selection
Once the Manual J load is known, Manual S guides equipment selection so the furnace, air conditioner, heat pump, or boiler is matched to that specific load: not rounded up "to be safe." Oversized equipment short-cycles, wears out faster, and does a worse job of controlling humidity than a correctly sized system running longer, steadier cycles.
Working with builders
New construction mechanical work only goes smoothly when it's coordinated with the framing, rough, and trim schedule, and with the other trades on site. We attend rough-in walkthroughs, work directly with electricians on equipment disconnects and low-voltage wiring, coordinate with plumbers on condensate lines and gas piping, and work punch lists with the builder's superintendent through closeout.
Multi-zone layouts for open-plan and two-story homes
Open-concept first floors and two-story layouts rarely have a uniform load across the whole house: a great room with south-facing glass and a vaulted ceiling behaves nothing like an upstairs bedroom over an unfinished garage. We use the room-by-room Manual J results to design zoning, whether that's a single system with ducted zone dampers or separate systems for separate levels, so each area is actually controlled to its own load instead of averaging comfort across a single thermostat.
Code compliance
- Compliance with New Hampshire's adopted residential energy code, based on IECC Climate Zone 6A requirements
- Duct sealing to reduce leakage: an increasingly common item verified by duct-leakage or blower-door testing on new builds
- Combustion air supply sized correctly for fuel-burning furnaces and boilers
- Mechanical ventilation sized to the home's tightness, since a well-sealed envelope needs planned fresh-air exchange rather than relying on incidental leakage
From plan review to commissioning
- 1
Plan review
We review the architectural plans early, ideally before framing, to identify mechanical closet locations, duct chase paths, and equipment placement while they're still cheap to change.
- 2
Manual J load calculation
We calculate the home's actual heating and cooling load room by room, using the home's orientation, envelope construction, window area and glazing, infiltration rate, and the southern NH winter design temperature (roughly 0°F) under IECC Climate Zone 6A.
- 3
Manual S equipment selection
With the load calculated, we select equipment (furnace, air conditioner, heat pump, or boiler) matched to that load rather than rounding up to the next standard size, which is the single biggest driver of oversized, short-cycling systems.
- 4
Manual D duct design
We design the duct system (trunk and branch sizing, static pressure budget, and return-air paths) so the selected equipment can actually deliver its rated airflow to every room, not just the rooms closest to the air handler.
- 5
Rough-in coordination
Ductwork, refrigerant line sets, and venting go in during the framing stage, coordinated with the builder's schedule and with the electrician and plumber for disconnects, condensate lines, and gas piping.
- 6
Trim-out
Registers, grilles, thermostats, and indoor/outdoor equipment are installed after drywall and finishes, alongside the builder's trim schedule.
- 7
Code compliance verification
We confirm duct sealing, combustion air, and mechanical ventilation meet the state's adopted residential energy code, and coordinate with any blower-door or duct-leakage testing required for the project.
- 8
Commissioning
Before handoff, we start up the system, verify refrigerant charge or combustion settings, balance airflow room to room, and walk the homeowner through thermostat operation and maintenance basics.
Read the full Manual J guide
Want the detail behind southern NH's design temperature, envelope assumptions, and how load calculations actually get built?
Read: Manual J Sizing in Southern NHFrequently asked
Manual J is the industry-standard method (published by ACCA) for calculating a home's actual heating and cooling load, room by room. It accounts for orientation, window area and glazing type, insulation levels, air infiltration, and the local design temperature: for southern NH, roughly 0°F on the coldest design day. Rule-of-thumb sizing (like a flat number of square feet per ton) ignores all of that and routinely oversizes equipment, which causes short-cycling, poor humidity control, and uneven comfort.
The right-sized furnace or heat pump connected to undersized or poorly laid-out ductwork won't deliver its rated performance. Manual D duct design calculates static pressure and sizes trunk and branch ducts so each room gets the airflow it needs. Undersized return air is one of the most common real-world problems we find: it starves the system, raises static pressure, and drives up energy use and noise regardless of how good the equipment is.
Southern New Hampshire is in IECC Climate Zone 6A, which sets minimum insulation, air sealing, and equipment efficiency requirements under the state's adopted energy code. Zone 6A assumptions, along with a roughly 0°F winter design temperature, are baked directly into the Manual J load calculation for any home we design a system for.
As early as plan review, ideally before framing. Duct chases, mechanical closets, and equipment locations are much cheaper to plan for on paper than to retrofit after framing is up. We coordinate directly with builders on scheduling: rough-in during framing, trim-out after drywall, and final commissioning near the end of the project.
Yes. New construction mechanical work depends on tight coordination with the general contractor's schedule and with the electrician (equipment disconnects and low-voltage wiring) and plumber (condensate lines, gas piping, combustion air). We attend rough-in and trim walkthroughs and work punch lists directly with the builder's superintendent.
Open floor plans and two-story layouts often have very different loads on different levels or in different areas at different times of day. We design zoning, either ducted zone dampers on a single system or multiple systems, based on the Manual J load by area, not a guess, so upstairs bedrooms and an open first floor don't fight each other on one thermostat.
Duct sealing and airtightness (verified in some cases by blower-door testing), combustion air supply for fuel-burning equipment, and mechanical ventilation requirements under the state's adopted residential energy code are the items that come up on nearly every project. We design and install to meet these requirements, not just to pass a rough inspection.
Building a new home?
Bring us in early: plan review is free and it's the cheapest stage to get mechanical design right.
