Here's the fact that surprises most homeowners: New Hampshire does not have a state HVAC contractor license. There's no single card a technician can hand you that says "licensed HVAC contractor, State of NH" the way a plumber or electrician can. What exists instead is a patchwork of narrower credentials, administered by the Board of Mechanical Safety and Licensing under the Office of Professional Licensure and Certification (OPLC), plus a federal certification that applies to anyone touching refrigerant. Because there's no single license to check, it's genuinely hard to tell a properly credentialed shop from a truck, a magnetic sign, and a Facebook page. Both can look identical in your driveway.
That doesn't mean an unlicensed installer is automatically a bad technician: some are very good at the mechanical work. But when something goes wrong ( a warranty claim gets denied, an inspector flags the install at resale, your insurer asks who did the work after a fire) you are the one holding the risk, not them. This post is about knowing exactly what to ask for, by name, so you're making that call with real information instead of a gut feeling about how confident someone sounded on the phone.
The credentials that actually exist in NH
Because there's no umbrella "HVAC license," different parts of the job are governed by different credentials. Knowing which one applies to which task is the whole trick.
| Type of work | Credential that should exist |
|---|---|
| Gas piping: running or modifying fuel gas lines | NH Fuel Gas Piping Installer license (Saf-Mec 305, issued by the Board of Mechanical Safety and Licensing) |
| Installing or servicing gas-fired equipment | NH Fuel Gas Installation Technician or Service Technician license (Saf-Mec 305) |
| Installing or servicing gas fireplaces, stoves, and hearth appliances | NH Hearth System Installation and Service Technician license (Saf-Mec 305) |
| Anyone touching refrigerant (charging, recovering, evacuating a system) | EPA Section 608 Technician Certification (federal, required nationwide: no NH-specific equivalent) |
| The company itself operating as an HVAC business in NH | Mechanical Business Entity license through OPLC |
| An apprentice-level worker on a gas job, under supervision | Fuel Gas Trainee registration (Saf-Mec 306): a separate registration, not one of the four licence classes, and should never be working unsupervised |
| Electrical work tied to the install (disconnects, new circuits, whips) | NH Electrician's license: a separate trade license entirely, often subcontracted |
Swipe to see the full table
Under Saf-Mec 305, New Hampshire recognizes four fuel gas licence classes: Piping Installer, Installation Technician, Service Technician, and Hearth System Installation and Service Technician. A "Trainee" credential also exists, but it's a separate registration under Saf-Mec 306, not one of the four licence classes: a trainee should always be working under a licensed supervisor, not solo.
Notice what's missing from that table: general ductwork, equipment selection, sizing, startup and commissioning of an all-electric heat pump system. None of that is licensed in New Hampshire at all. A company can legally install a ducted heat pump system with zero state credential beyond the business entity license, as long as no gas piping or refrigerant work triggers the other two. That's the gap that lets undertrained outfits operate, and it's exactly why the manufacturer's brand reputation, the installer's actual track record, and a properly written proposal matter more here than they would in a state with a real contractor license.
What to actually ask for: by name
Vague questions get vague answers. "Are you licensed?" invites a confident "yes" from someone who technically holds one credential out of three relevant ones. Ask for specifics instead:
- "What's your Fuel Gas Fitter license number and class?" (if the job involves any gas piping: furnace, boiler, water heater conversion). Write the number down.
- "Who on the crew holds EPA 608 certification, and will they be the one handling the refrigerant?" (relevant for any heat pump, mini-split, or AC job).
- "What's your Mechanical Business Entity license number?" This is the company-level license, separate from any individual's card.
- Look up every number they give you yourself on the OPLC public licence lookup before you sign anything. Don't take a photo of a card as proof: verify it against the state database directly.
- Ask for a Certificate of Insurance issued directly by the insurance carrier or broker, naming you as the certificate holder: not a PDF the contractor forwards from their own files. A carrier-issued certificate can be verified by calling the agent listed on it; a forwarded PDF can be edited in five minutes.
- Ask specifically: "Will you be pulling a mechanical/gas permit for this job with the town, and will there be a final inspection?" Get the answer in writing on the proposal.
- Ask for the make, model number, and AHRI certificate reference number of the equipment being quoted, not just "a 3-ton heat pump." A real proposal has this. A vague one doesn't.
- Ask to see the load calculation in writing, not just a verbal "this size will work fine." See our Manual J sizing post for why this matters more than almost anything else on the quote.
Why the permit matters
A permit isn't paperwork for its own sake. When a licensed contractor pulls a mechanical or gas permit with your town, a third-party inspector ( someone with no financial stake in the job) checks the install against code before it's signed off. That inspection is what protects you at resale (undocumented HVAC work is a common flag in home inspections), and it's often what your insurer wants to see if there's ever a claim involving the equipment. The homeowner is technically allowed to pull certain permits themselves in some NH towns, but on gas or major electrical work, the permit should be pulled by the licensed contractor performing the work, in their name, not yours. If a contractor tells you "we don't bother with permits for jobs like this" or "the town doesn't really check residential HVAC," that's a straightforward answer to walk away.
Red flags worth taking seriously
- A meaningful discount for paying cash, especially if it's framed as "off the books" or tied to skipping a permit.
- No written, itemized estimate: just a verbal number or a text message with a total and no line items.
- No model numbers, capacity, or AHRI reference numbers anywhere on the proposal.
- Pressure to sign the same day, especially paired with "this price is only good today." A legitimate quote for a multi-thousand-dollar system should hold for at least a week or two.
- Refusal to provide a load calculation in writing, or a dismissive answer like "we've been doing this thirty years, we don't need to run the numbers."
- A certificate of insurance that's a screenshot or a scan forwarded by the contractor rather than something you can verify with the carrier directly.
If you're weighing a repair against a full system replacement and want to know how licensing and permitting fit into that decision, our repair-or-replace guide walks through the rest of that math. You can also read more about our own licensing and background, or reach out with questions before you sign anything.
For more about this work, see our Heat Pump Installation in southern NH page or request a free estimate.
Dana Borriello: Dana Borriello founded Service One Heating and Cooling in 2013 and still runs service calls across southern New Hampshire. He writes here about the questions homeowners actually ask on the truck.
